Life Size 3D Printed Thors Hammer (Mjolnir)
- 6 лет назад
Its finally time for my 3D printed Mjolnir to reveal itself to the world. I designed this in Tinkercad and printed it on my Robo 3D printer. Then we painted and finished it up to make it look like it does in the s. This Mjolnir is ually modeled after the one in The Dark World. Let me know what you think of it!\r
\r
3D Files: \r
Thingiverse: \r
YouMagine: \r
PinShape: \r
Cults: \r
MyMiniFory: \r
\r
There are several steps listed in the video to aid you in the post processing of this print. Ill try to be as detailed here as possible.\r
\r
Step 0: Print all the parts.\r
\r
Step 1: Sand the parts down as much as possible. The details on the handle and the outside of the hammer can be pretty hard to get smooth, but do your best. The sides of the hammer should be completely smooth to the touch though. Start with a coarse grit sandpaper in the ballpark of 100 grit. Then move up to 400 or above to get the best results.\r
\r
Step 2: Glue the parts together. Use the printed pins to hold the parts in place, then apply glue to those pins to adhere them together. I used a Gorilla Glue Two Part Epoxy, glued the parts and held them for a bit until they dried. Then once the parts are together, take a paint brush or something similar to apply the epoxy generously over any cracks or seams you want to cover. Then once the glue has dried completely, sand the areas over seams to get those smoothed down as well.\r
\r
Step 3: Prime the hammer. We chose to use a black spray primer from Krylon. Coat the hammer at least twice, letting it dry completely in between coats. Just lightly spray across the surface using a normal spray painting technique. Dont stress too much about the detailed areas at this point.\r
\r
Step 4: Painting the hammer. We used a Hammered Metal spray paint. Specifically silver colored. Apply 3 coats of this, letting it dry completely in between. If needed, you can sand any rough areas in between coats. Just use your judgement on what looks best. The paint should fully cover the hammer.\r
\r
Step 5: Paint the handle. For this youll need a paint brush and some brown acrylic paint. Paint the brown on the lower areas of the handle, leaving the silver rings and base of the handle as is. Make use of multiple brushes to get into hard to reach areas. Apply 3 coats of this to get a smooth, but plentiful coverage of paint. You can always go back over the details on the handle with silver paint if you need to.\r
\r
Step 6: Apply a wash. I wont go into a ton of detail about the wash. You can YouTube applying a wash to miniatures if you want more details. We took some silver and black acrylic paint, mix it and watered it down significantly then applied it to the details on the handle and on the sides of the hammer. Use a paper towel or spare paint brush to dab off excess. This will give the recessed areas a more defined shadow.\r
\r
Step 7: Rough it up. This step involves taking sand paper to the paint on the bulk of the hammer to give it a worn and used look. Go around the edges and just lightly sand it to give it a more textured look. Then take some of your paper towels you used to clean off the wash and lightly dust that darker color across the body for even more texture.\r
\r
Step 8: Apply a finish coat. You can get some spray clear coat and just spray the whole thing once its completely dry and done. This will help protect it from damage like scratches to the paint.\r
\r
====================================\r
Links to Videos shown in my end card:\r
3D Printed R2D2: \r
Details on Curved Objects in Tinkercad: \r
New Vlog: \r
\r
Thanks for Watching!\r
Follow me on Twitter:
\r
3D Files: \r
Thingiverse: \r
YouMagine: \r
PinShape: \r
Cults: \r
MyMiniFory: \r
\r
There are several steps listed in the video to aid you in the post processing of this print. Ill try to be as detailed here as possible.\r
\r
Step 0: Print all the parts.\r
\r
Step 1: Sand the parts down as much as possible. The details on the handle and the outside of the hammer can be pretty hard to get smooth, but do your best. The sides of the hammer should be completely smooth to the touch though. Start with a coarse grit sandpaper in the ballpark of 100 grit. Then move up to 400 or above to get the best results.\r
\r
Step 2: Glue the parts together. Use the printed pins to hold the parts in place, then apply glue to those pins to adhere them together. I used a Gorilla Glue Two Part Epoxy, glued the parts and held them for a bit until they dried. Then once the parts are together, take a paint brush or something similar to apply the epoxy generously over any cracks or seams you want to cover. Then once the glue has dried completely, sand the areas over seams to get those smoothed down as well.\r
\r
Step 3: Prime the hammer. We chose to use a black spray primer from Krylon. Coat the hammer at least twice, letting it dry completely in between coats. Just lightly spray across the surface using a normal spray painting technique. Dont stress too much about the detailed areas at this point.\r
\r
Step 4: Painting the hammer. We used a Hammered Metal spray paint. Specifically silver colored. Apply 3 coats of this, letting it dry completely in between. If needed, you can sand any rough areas in between coats. Just use your judgement on what looks best. The paint should fully cover the hammer.\r
\r
Step 5: Paint the handle. For this youll need a paint brush and some brown acrylic paint. Paint the brown on the lower areas of the handle, leaving the silver rings and base of the handle as is. Make use of multiple brushes to get into hard to reach areas. Apply 3 coats of this to get a smooth, but plentiful coverage of paint. You can always go back over the details on the handle with silver paint if you need to.\r
\r
Step 6: Apply a wash. I wont go into a ton of detail about the wash. You can YouTube applying a wash to miniatures if you want more details. We took some silver and black acrylic paint, mix it and watered it down significantly then applied it to the details on the handle and on the sides of the hammer. Use a paper towel or spare paint brush to dab off excess. This will give the recessed areas a more defined shadow.\r
\r
Step 7: Rough it up. This step involves taking sand paper to the paint on the bulk of the hammer to give it a worn and used look. Go around the edges and just lightly sand it to give it a more textured look. Then take some of your paper towels you used to clean off the wash and lightly dust that darker color across the body for even more texture.\r
\r
Step 8: Apply a finish coat. You can get some spray clear coat and just spray the whole thing once its completely dry and done. This will help protect it from damage like scratches to the paint.\r
\r
====================================\r
Links to Videos shown in my end card:\r
3D Printed R2D2: \r
Details on Curved Objects in Tinkercad: \r
New Vlog: \r
\r
Thanks for Watching!\r
Follow me on Twitter: